Strictly preventing all kinds of impurities from entering the plating solution is an important aspect to ensure the stable performance of the plating solution. The main ways for impurities to enter the plating solution are: dissolution of the anode; Chemical materials; Cleaning water and cleaning operation; The influence of the environment, etc. If all these can be strictly controlled, then the harm of impurities to the performance of the plating solution will be fundamentally improved.
Quality control of the anode system
During the electroplating process, the metal anode will undergo electrochemical dissolution and chemical dissolution. The metal is transformed into metal ions to balance the deposition of metal ions in the plating solution and consume the coating. Meanwhile, the metal impurities contained in the anode metal also enter the plating solution. To slow down the accumulation rate of impurity ions in the plating solution and reduce their harm to the performance of the plating solution and the quality of the coating, pure metals with higher purity grades and lower impurity content should be selected as metal anodes. To ensure the stability of the plating solution's performance, Grade 1 or Grade 0 pure metals are usually used as anode materials, and the minimum requirement should not be lower than grade 1. The lower the purity grade, the greater the content of impurities in the metal. Take zinc anodes as an example. The content of lead impurities in grade 2 pure zinc anodes is four times that of grade 1 pure zinc anodes and six times that of grade 0 pure zinc anodes. For instance, the content of copper impurities in grade 1 pure nickel anodes is 20 times that of grade 0 pure nickel anodes.
Some electroplating enterprises, in order to obtain anodes that meet their own requirements in terms of size, shape or alloy composition, often smelt and cast pure metal ingots themselves to process anodes. Due to the lack of professional knowledge and equipment for non-ferrous metal smelting, the self-made anodes have various defects such as coarse crystals, loose structure, numerous pores, a large number of non-metallic inclusions, and an increase in impurity content. After use, it is very likely to cause an increase in anode sludge in the plating solution, an accelerated accumulation of impurities, and turbidity of the plating solution, directly endangering the process performance of the plating solution and the quality of the coating. In severe cases, the plating solution has to be shut down for treatment. To ensure the quality of non-standard anodes processed from pure metal ingots, electroplating enterprises should formulate enterprise standards for processing anodes, clearly stipulate technical requirements, and entrust professional anode processing factories with quality assurance capabilities to manufacture them.
In production, insoluble anodes are often used to control the rapid increase of metal ion content in the plating solution or as auxiliary anodes for electroplating complex parts. The metallic materials used to make insoluble anodes must be those that do not dissolve when placed in the plating solution under the condition of electricity. Materials commonly used to make insoluble anodes include electrical iron, 10 low-carbon steel, nickel-plated steel plates, 18-8 chromium-nickel austenitic stainless steel, platinum, titanium and titanium alloys, lead-antimony alloys, etc.
Titanium baskets are widely used in electroplating production because they can fully utilize anode materials. However, it is necessary to keep the titanium baskets at a relatively high anode material loading density all the time, so that the anode metal can dissolve under a relatively low potential. This not only saves electricity but also ensures uniform dissolution and reduces the generation of anode sludge. Conversely, not only will the anode dissolution be uneven, but also the resistance of the system will increase, causing the anode potential to rise. Sometimes, the titanium basket will also suffer from electrochemical corrosion, contaminating the plating solution and making the titanium basket prone to damage.
Improving the purity of anode materials, enhancing the processing quality of anodes, and increasing the active components in anodes can significantly reduce the generation of anode slime, but it cannot completely eliminate it. To ensure the cleanliness of the plating solution, it is still necessary to install an anode bag on the outer surface of the metal anode or titanium basket. Anode bags are usually made of fabric materials, but the fabric materials must have sufficient corrosion resistance in the plating solution to prevent the anode bags from being corroded and damaged due to long-term immersion in the plating solution, which could cause anode slime to re-fall into the plating solution and organic contamination. At present, the widely used material is polypropylene fiber cloth. The fabric should have a certain thickness and strength, as well as a certain degree of density. It should not allow the anode slime to pass through, but also should not hinder the diffusion movement of various ions in the plating solution.
Prevent the entry of impurities due to process factors
①Improper design of the hanger makes the parts not firmly attached, causing them to fall into the plating solution. If they cannot be removed in time, it will lead to corrosion of the parts, which is another important factor causing contamination of the plating solution.
② If the copper conductive rods on the plating bath have not undergone anti-corrosion treatment or if the structural design of the conductive system is not reasonable enough, the copper conductive system will be corroded, resulting in patina and other attachments on the surface, which will inevitably fall into the plating solution.
③ Improper material selection of the steam heating tubes or electric heating tubes in the plating tank, or poor insulation between the heating tubes and the tank body during installation, leads to corrosion of the heating tubes.
④ If the connection part between the anode and the anode copper hook is not reliably insulated, galvanic corrosion will occur at this part, and the corrosion products will fall into the plating solution.
⑤If the quality of the pre-treatment of parts is poor, the oil stains, polishing paste, rust and other contaminants that have not been completely removed from the surface may enter the plating solution.
⑥ The complex shape of the parts makes it easy for liquid to accumulate, or the momentum of the cleaning water flow is too small, resulting in incomplete cleaning of the parts and bringing the residual liquid from the previous process into the solution.
When electroplating some parts with special shapes, such as pipe fittings, deep hole parts, and parts with grooves, due to the limited dispersion ability of the plating solution or the absence of auxiliary anodes, local surfaces will be corroded by deposited coatings.
The occurrence of the above-mentioned phenomena is mostly caused by improper operation, defects in the design of tooling equipment, mistakes in the design of process regulations and other factors. Therefore, effective measures must be taken to prevent these phenomena from happening.
Country:China
Add:Baoti road,Jintai,Baoji city,Shaanxi,China
Cel/Whatsapp :+86 18309262795
Email:annie@jmyunti.com
Website:www.jm-titanium.com








